Szczegóły publikacji

Opis bibliograficzny

Kinetics of gases emission from surface layers of sand moulds / J. ZYCH, J. MOCEK, N. KAŹNICA // Archives of Foundry Engineering / Polish Academy of Sciences. Commission of Foundry Engineering ; ISSN 1897-3310. — Tytuł poprz.: Archiwum Odlewnictwa. — 2018 — vol. 18 iss. 1, s. 222–226. — Bibliogr. s. 225–226, Abstr.

Autorzy (3)

Słowa kluczowe

moulding sandschemical bindersgasesmoulding sandsurface layerkinetics of gas emission

Dane bibliometryczne

ID BaDAP113501
Data dodania do BaDAP2018-05-10
Tekst źródłowyURL
DOI10.24425/118841
Rok publikacji2018
Typ publikacjiartykuł w czasopiśmie
Otwarty dostęptak
Creative Commons
Czasopismo/seriaArchives of Foundry Engineering

Abstract

Gas emission from casting moulds, cores and coatings applied for sand and permanent moulds is one of the fundamental reasons of casting defects occurrence. In the previous studies, gas emission was measured in two ways: normalized, in which the evolving gas volume was measured during heating of the moulding sand sample in a sealed flask, or by measuring the amount of gas from sand core (sample) which is produced during the pouring of liquid metal. After the pouring process the sand mould is heated very unequally, the most heated areas are layers adjacent to the liquid metal. The emission of gas is significantly larger from the surface layer than from the remaining ones. New, original method of measuring kinetics of gas emission from very thin layers of sand moulds heated by liquid metal developed by the authors is presented in the hereby paper. Description of this new method and the investigation results of kinetics of gas emission from moulding sand with furan and alkyd resin are shown. Liquid grey cast iron and Al-Si alloy were used as a heat source in the sand moulds. Comparison of the kinetics of gas emission of these two kinds of moulding sands filled with two different alloys was made. The momentary metal temperature in sand mould was assigned to the kinetics of gas emission, what creates a full view of the possibility of formation of casting defects of the gaseous origin. Moulding sand with alkyd resin is characterized by larger gas emission; however gases are emitted slower than in the case of moulding sands with furan resin. This new investigation method has a high repeatability and is the only one which gives a full view of phenomenon’s in the surface layer which determines quality of the casings. The obtained results are presented on several graphs and analyzed in detail. They have a great application value and can be used in the production of iron as well as light metal alloy castings.

Publikacje, które mogą Cię zainteresować

artykuł
#111961Data dodania: 10.2.2018
Gases emission from surface layers of sand moulds and cores stored under the humid air conditions / N. KAŹNICA, J. ZYCH, J. MOCEK // Archives of Foundry Engineering / Polish Academy of Sciences. Commission of Foundry Engineering ; ISSN 1897-3310. — Tytuł poprz.: Archiwum Odlewnictwa. — 2017 — vol. 17 iss. 4, s. 79–84. — Bibliogr. s. 84, Abstr. — Publikacja dostępna online od: 2018-01-16
fragment książki
#109783Data dodania: 30.11.2017
Gases emission from surface layers of sand moulds and cores stored under the humid air conditions / N. KAŹNICA, J. ZYCH, J. MOCEK // W: KiKM 2017 [Dokument elektroniczny] : „Krzepnięcie i krystalizacja metali 2017” : 58. międzynarodowa konferencja naukowa ; XXV Międzynarodowy Salon Przemysłu Obronnego MSPO 2017 : 6th–8th September 2017, Kielce–Solec Zdrój : materiały konferencyjne = ”Solidification and crystallization of metals 2017” : 58th international scientific conference ; 25th international defence industry exhibition MSPO 2017 : proceedings. — Wersja do Windows. — Dane tekstowe. — [Kielce : s. n.], [2017]. — 1 dysk optyczny. — S. [1–6]. — Wymagania systemowe: Adobe Reader ; napęd CD-ROM. — Bibliogr. s. [6], Abstr.